Author Topic: Window and right angle connector questions.  (Read 4471 times)

0 Members and 1 Guest are viewing this topic.

GreekMan

  • Prepper
  • Full Member
  • *
  • Posts: 202
  • Karma: 14
  • Gender: Male
    • GreekPreparedness
Window and right angle connector questions.
« on: August 14, 2017, 12:21:25 PM »
Ok one more novice question, since i finally bought me a crimper and i have started assembling a stock of connectors, not only for building the few cables that I need, but having some extras for just in case. here goes....

what do you think of those connectors that are right angle (rg58 and Rg174 size).
I kinda like the one I have, it allows for some flex/tension relief, and i can reuse it (with new crimp sleeves)

the window ones are kinda the same thing

and BTW, I have also bothered the group with the clamp on ones some time ago. kinda want to have some for "in the field" assembly*

So....are there serious performance reasons NOT to use them?

* if you care to read a story behind it,
I once moved to a foresaken place for a seasonal job and as luck may have it, I had a broken connection on my mobile cable the first day there. No spares and no tools either. I had to put the mobile antenna on the HT and get the help of a friendly local HAM.
Since them i carry spares and two soldering irons (12V and 220V) in the car.

ghrit

  • Prepper
  • Full Member
  • *
  • Posts: 279
  • Karma: 22
Re: Window and right angle connector questions.
« Reply #1 on: August 14, 2017, 03:40:19 PM »
I use 90 degree fittings extensively to avoid bending coax in tight places.  Not familiar with "through the window" fittings.
There are two kinds of ships.  Submarines and targets.
KB3ZMF        FN21dy
Amateur Extra Class,  VE
www.survivalmonkey.com

Tevin

  • Prepper
  • Full Member
  • *
  • Posts: 455
  • Karma: 29
  • Rhymes with heaven.
Re: Window and right angle connector questions.
« Reply #2 on: August 14, 2017, 07:44:19 PM »
Any connector will have some kind of loss. There is no way around it.

The loss is barely measurable and if you need the right angle connector, then there isn't another option.

I occasionally use them and they work fine.

I say go for it and don't sweat the small stuff.

GreekMan

  • Prepper
  • Full Member
  • *
  • Posts: 202
  • Karma: 14
  • Gender: Male
    • GreekPreparedness
Re: Window and right angle connector questions.
« Reply #3 on: August 15, 2017, 07:07:53 AM »
I use 90 degree fittings extensively to avoid bending coax in tight places.  Not familiar with "through the window" fittings.

this is one of them
http://www.ebay.com/itm/1pce-Connector-UHF-SO239-female-jack-bulkhead-crimp-RG316-RG174-LMR100-COAXIAL/222098615225?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2055119.m1438.l2649
center pi is not removable, but there is a window to solder the coax wire to.

I did not find anyone selling spare center pins, but sleeves are available. So redoing/reusing the window connectors is easy.

yes i am cheap, but as preppers too we should plan ahead for limited resources.

ghrit

  • Prepper
  • Full Member
  • *
  • Posts: 279
  • Karma: 22
Re: Window and right angle connector questions.
« Reply #4 on: August 15, 2017, 08:06:38 AM »
this is one of them
http://www.ebay.com/itm/1pce-Connector-UHF-SO239-female-jack-bulkhead-crimp-RG316-RG174-LMR100-COAXIAL/222098615225?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2055119.m1438.l2649
center pi is not removable, but there is a window to solder the coax wire to.

I did not find anyone selling spare center pins, but sleeves are available. So redoing/reusing the window connectors is easy.

yes i am cheap, but as preppers too we should plan ahead for limited resources.
OK, now I know what it is.  I got lost on "window" fitting term.  Off hand I cannot imagine needing one unless rebuilding a chassis, but it can't hurt to have one or two in the box of oddies on the back shelf, just in case.
There are two kinds of ships.  Submarines and targets.
KB3ZMF        FN21dy
Amateur Extra Class,  VE
www.survivalmonkey.com

Tempstar

  • Full Member
  • ***
  • Posts: 372
  • Karma: 23
  • Gender: Male
  • Extra, VE, SC Agency MARS, AUXCOMM, ARES/RACES
Re: Window and right angle connector questions.
« Reply #5 on: August 19, 2017, 08:13:23 AM »
We use crimp connectors at the TV station always. Take your time and be neat and they give no problems. Always use the right crimp tool and they are better than solder IMHO.
"Preparedness is a lot more than just buying stuff"